
中空玻璃起霧進水,問題多半出在這道工序
時間:2026-10-14 來源:http://www.whooo.net/ 發布人:昌盛機械
中空玻璃用久了起霧、進水、結露,業主投訴不斷,廠家返工成本高。很多人以為是密封膠質量問題,其實根源往往在生產線上——合片、打膠、壓合這幾道工序沒控制好,再好的膠也白搭。
Hollow glass has been fogging, water ingress, and condensation for a long time, leading to continuous complaints from homeowners and high rework costs for manufacturers. Many people think it's a quality issue with the sealant, but in fact, the root cause often lies in the production line - the processes of laminating, gluing, and pressing are not well controlled, and even the best sealant is useless.

一、鋁條折彎決定第一道密封
1、 Aluminum strip bending determines the first seal
鋁間隔條是骨架,也是干燥劑的容器。折彎精度不夠,四角對不齊,合片后密封膠填充不均,水汽就從縫隙進去了。全自動折彎機比手工折彎一致性高得多,角度誤差小,插角緊密。折彎后要馬上灌裝分子篩,暴露時間長了干燥劑吸潮失效,等于白裝。
Aluminum spacer bars are the skeleton and also the container for desiccants. The bending accuracy is insufficient, the four corners are not aligned, and the sealant is not evenly filled after lamination, causing water vapor to enter through the gaps. Fully automatic bending machines have much higher consistency than manual bending, smaller angle errors, and tighter insertion angles. After bending, the molecular sieve should be filled immediately. If the desiccant fails to absorb moisture after a long exposure time, it is equivalent to white packaging.
二、丁基膠涂布是隱形防線
2、 Butyl rubber coating is an invisible defense line
丁基膠是第一道密封,直接決定水汽滲透率。涂布溫度、壓力、速度要匹配,溫度低了涂不勻,高了膠體老化。膠層厚度一般0.3到0.5毫米,太薄密封不夠,太厚浪費還影響合片。很多小廠這道工序靠手感,批量質量不穩定,出了問題也查不出原因。
Butyl rubber is the first seal that directly determines the water vapor permeability. The coating temperature, pressure, and speed should be matched. If the temperature is low, the coating will not be uniform, and if it is high, the colloid will age. The thickness of the adhesive layer is generally 0.3 to 0.5 millimeters. If it is too thin, the seal will not be sufficient, and if it is too thick, it will waste and affect the lamination. Many small factories rely on hand feel for this process, and the batch quality is unstable. Even if there are problems, the cause cannot be identified.
三、雙組份打膠看配比和混合
3、 Two component gluing depends on the ratio and mixing
第二道密封用雙組份膠,A膠和B膠配比不對,要么固化不完全、要么發脆開裂。打膠機要能準確計量、充分混合,混合不均的膠局部強度差,時間一長就滲漏。打膠后要靜置固化,環境溫濕度也要控制,冬天固化慢,不能急著搬運。
The second seal uses two-component adhesive, and the ratio of A adhesive to B adhesive is incorrect, resulting in incomplete curing or brittle cracking. The glue machine should be able to accurately measure and mix thoroughly. Uneven mixing of glue can result in poor local strength and leakage over time. After gluing, it should be left to cure and the temperature and humidity of the environment should be controlled. Curing is slow in winter and cannot be rushed during transportation.
四、充氣中空要控好濃度
4、 Control the concentration of inflatable hollows well
做Low-E充氬氣的中空玻璃,充氣濃度直接影響保溫性能。濃度不夠等于沒充,濃度虛標還涉及驗收風險。充氣設備要有濃度檢測,合片后盡快封邊,避免氣體逸散。
The filling concentration of Low-E argon gas directly affects the insulation performance of insulating glass. Insufficient concentration is equivalent to not charging, and false concentration labeling also involves acceptance risks. Inflating equipment should have concentration detection, and the edges should be sealed as soon as possible after closing to avoid gas leakage.
五、選生產線看三點
5、 Three points to consider when selecting a production line
一看設備精度和穩定性,折彎角度、打膠配比、壓合平行度這些參數能不能長期保持。二看自動化程度,人工干預越多,一致性越差。三看售后,密封膠固化問題往往在幾個月后才暴露,廠家能不能快速響應很關鍵。
When it comes to the accuracy and stability of the equipment, can parameters such as bending angle, glue ratio, and parallelism be maintained for a long time. Looking at the degree of automation, the more manual intervention there is, the worse the consistency. After checking the after-sales service, the problem of sealant curing is often exposed several months later, and it is crucial for the manufacturer to respond quickly.
中空玻璃的壽命,藏在生產線的每一道工序里。
The lifespan of insulating glass is hidden in every process of the production line.
- 中空玻璃起霧進水,問題多半出在這道工序 2026/10/14
- 立著裝還是橫著裝,中空玻璃打膠這道工序怎么選 2026/10/12
- 膠嘴這個位置差0.5毫米,中空玻璃就等于白做 2026/10/09
- 雙組份打膠機:比例對了,膠才不白打 2026/10/05
- 全自動鋁條折彎機,中空玻璃鋁框加工核心利器 2026/09/29
- 全自動封膠線,中空玻璃廠升級繞不開的一道坎 2026/09/24
- 設備選型不對,密封失效是遲早的事 2026/09/23
- 中空玻璃生產線:別讓“手工中空”,吃掉你的利潤 2026/09/21
- 中空玻璃生產線:清洗出來不干凈,先查這五個地方 2026/09/18
- 中空玻璃生產線怎么確保玻璃的參數達標? 2026/09/16
產品分類Product categories
聯系我們Contact us
- 咨詢熱線:0531-85717458 13705446998
- 公司地址: 山東省德州市齊河安頭鄉企巢工業園
- 掃碼聯系我們:

當前位置:



