中空玻璃生產線使用一段時間后，“玻璃清洗出來不干凈”是非常常見的問題。原因很少是單一的，通常需要按順序排查五個地方。

After using the insulated glass production line for a period of time, the most common problem is that the glass is not cleaned thoroughly. The reason is rarely singular, usually requiring a sequential investigation of five areas.

第一，檢查水質。 清洗水路是循環系統，如果長期不換水，水中的雜質和油污會(huì )越來越多，噴淋到玻璃上反而造成二次污染。先更換清洗水，清理風機入口過濾網。

Firstly, check the water quality. The cleaning water system is a circulating system. If the water is not changed for a long time, impurities and oil stains in the water will increase, and spraying onto the glass will cause secondary pollution. Replace the cleaning water first and clean the inlet filter of the fan.

第二，觀察污漬的“形狀”。 如果污漬呈均勻的橫條狀，檢查非常后一道膠輥表面是否有贓物。如果呈斜狀痕跡，檢查非常后一道膠輥中間是否有縫隙，如有，調整膠輥軸承座彈簧。形狀不同，病灶位置不同。

Secondly, observe the "shape" of the stain. If the stain appears as a uniform horizontal strip, check if there is any dirt on the surface of the last rubber roller. If there are diagonal marks, check for any gaps in the middle of the last rubber roller. If so, adjust the rubber roller bearing seat spring. Different shapes result in different lesion locations.

第三，檢查風刀和干燥效果。 清洗后如果玻璃表面殘留水漬，風刀的角度、風力或加熱功能可能出了問題。干燥段的大風力傾斜風刀需要定期檢查出風是否均勻，加熱功能是否正常工作。

Thirdly, check the air knife and drying effect. If water stains remain on the glass surface after cleaning, there may be issues with the angle, wind force, or heating function of the wind blade. The high wind inclined blade in the drying section needs to be regularly checked for uniform air flow and proper heating function.

第四，檢查清洗段的毛刷磨損。 毛刷使用一段時間后會(huì )變形或脫落，導致清洗盲區。多對高密度軟毛刷需要定期檢查磨損狀態，必要時更換。

Fourth, check the wear of the brush in the cleaning section. After using the brush for a period of time, it may deform or fall off, causing cleaning blind spots. Multiple pairs of high-density soft bristle brushes need to be regularly checked for wear and replaced if necessary.

第五，檢查傳送輥是否沾染污物。 傳送輥長期接觸玻璃和清洗液，表面可能積累污垢，玻璃經過時被“蹭臟”。耐酸堿橡膠傳動輥需要定期清潔或更換。

Fifth, check whether the conveyor roller is contaminated with dirt. The conveyor roller may accumulate dirt on the surface due to long-term contact with glass and cleaning solution, and the glass may be "scratched" when passing by. The acid alkali resistant rubber transmission roller needs to be cleaned or replaced regularly.

清洗不干凈的問題，九成出在這五個地方。按順序排查，比盲目調整設備參數更有效。

Ninety percent of the problem of unclean cleaning lies in these five areas. Sorting in order is more effective than blindly adjusting equipment parameters.