
雙組份打膠機:比例對了,膠才不白打
時間:2026-10-05 來源:http://www.whooo.net/ 發布人:昌盛機械
雙組份打膠機用起來簡單,調起來麻煩。A膠和B膠的比例差一點,膠縫的固化強度就天差地別。很多施工問題——膠條發軟、固化不完全、粘結力不夠——根源不在膠水,而在配比。
The two-component glue dispenser is easy to use but troublesome to adjust. Even a slight difference in the ratio of glue A to glue B can lead to a significant difference in the curing strength of the glue seam. Many construction issues - such as soft glue strips, incomplete curing, and insufficient bonding strength - stem not from the glue itself, but from the mixing ratio.

比例控制是雙組份打膠機的命門。 中空玻璃二道密封常用的雙組份聚硫膠或硅酮膠,A組份(基料)和B組份(固化劑)的混合比通常在6:1到14:1之間。比例泵是控制這個配比的核心部件,通過松開比例杠桿上的鎖緊螺釘來調整內外比例。調整之后建議試打,觀察混合后的膠條顏色是否均勻一致,有無條紋或色塊——顏色不均說明混合不到位,固化強度就沒有保證。比例精度誤差需要控制在±2%以?xún)?,這是行業基本要求。
Proportion control is crucial for a two-component glue dispensing machine. The commonly used two-component polysulfide glue or silicone glue for the secondary sealing of insulating glass has a mixing ratio of component A (base material) to component B (curing agent) typically ranging from 6:1 to 14:1. The proportion pump is the core component for controlling this ratio, and the internal and external proportions can be adjusted by loosening the locking screw on the proportion lever. After adjustment, a trial dispensing is necessary to observe whether the color of the mixed glue strip is uniform, without stripes or color blocks - uneven color indicates incomplete mixing, and the curing strength cannot be guaranteed. The proportion accuracy error needs to be controlled within ±2%, which is a basic requirement in the industry.
出膠量調節不止一個旋鈕。 很多人以為調出膠量就是轉一下氣源處理器,實際上有多層控制:氣源處理器負責總出膠量的粗調,逆時針加大、順時針減??;供膠時間通過控制器在0.001-99.99秒范圍內準確設定;點膠閥氣缸行程也影響單次出膠量。這幾個參數需要配合調整,單調一個往往達不到想要的效果。
There is more than one knob for adjusting the glue output. Many people mistakenly believe that adjusting the glue output simply involves turning the air source processor. In reality, there are multiple layers of control: the air source processor is responsible for the coarse adjustment of the total glue output, with counterclockwise increasing and clockwise decreasing; the glue supply time can be precisely set within the range of 0.001-99.99 seconds through the controller; and the stroke of the dispensing valve cylinder also affects the single glue output. These parameters need to be adjusted in conjunction, as adjusting one alone often fails to achieve the desired effect.
固化劑系統建議全封閉。 這是選設備時容易忽略的細節。固化劑(B膠)接觸空氣會(huì )吸收水分,導致結晶、堵塞管路。好的雙組份打膠機固化劑系統采用全封閉設計,杜絕空氣混入。如果設備用了半年就頻繁堵B管,大概率是密封出了問題。
The curing agent system must be fully enclosed. This is a detail that is often overlooked when selecting equipment. When exposed to air, the curing agent (B glue) absorbs moisture, leading to crystallization and pipeline blockage. A good two-component glue dispenser features a fully enclosed design to prevent air from mixing in. If the B tube of the equipment frequently gets blocked after just half a year of use, there is a high probability that there is a problem with the seal.
日常清洗比修設備重要。 每次工作結束后建議立即清洗混合器和膠槍?zhuān)趴諝堄嗄z料。雙組份膠一旦在混合腔里固化,清理起來出彩其費時?;旌掀鹘ㄗh每隔15個工作日深度清洗一次。氣路油霧器要定期檢查潤滑油,油水分離器每天排放積水。
Routine cleaning is more important than equipment maintenance. After each work session, the mixer and glue gun must be cleaned immediately to drain any remaining glue material. Once the two-component glue cures in the mixing chamber, cleaning becomes extremely time-consuming. It is recommended to deep clean the mixer every 15 working days. The gas path oil mist device should be regularly checked for lubricating oil, and the oil-water separator should be drained daily.
雙組份打膠機的邏輯很實在:比例對了,膠才有強度;管路干凈,設備才不罷工。調好這兩個,比買貴的設備更管用。
The logic behind a two-component glue dispenser is straightforward: the right proportion ensures the glue has strength; clean pipelines prevent equipment malfunctions. Adjusting these two aspects is more effective than purchasing expensive equipment.
本文由雙組份打膠機友情奉獻.更多有關的知識請點擊:http://www.whooo.net 我們將會(huì )對您提出的疑問進行詳細的解答,歡迎您登錄網站留言。
This article is kindly contributed by a two-component glue dispenser. For more relevant information, please visit: http://www.whooo.net. We will provide detailed answers to your questions. You are welcome to log in and leave a message on our website.
- 雙組份打膠機:比例對了,膠才不白打 2026/10/05
- 全自動鋁條折彎機,中空玻璃鋁框加工核心利器 2026/09/29
- 全自動封膠線,中空玻璃廠升級繞不開的一道坎 2026/09/24
- 設備選型不對,密封失效是遲早的事 2026/09/23
- 中空玻璃生產線:別讓“手工中空”,吃掉你的利潤 2026/09/21
- 中空玻璃生產線:清洗出來不干凈,先查這五個地方 2026/09/18
- 中空玻璃生產線怎么確保玻璃的參數達標? 2026/09/16
- 中空玻璃生產線立著運行更具有效率 2026/09/14
- 全自動封膠線是中空玻璃密封的智能升級 2026/09/12
- 中空玻璃加工設備整套生產線的制作流程 2026/09/10
產品分類Product categories
聯系我們Contact us
- 咨詢熱線:0531-85717458 13705446998
- 公司地址: 山東省德州市齊河安頭鄉企巢工業園
- 掃碼聯系我們:

當前位置:



