
膠嘴這個位置差0.5毫米,中空玻璃就等于白做
時間:2026-10-09 來源:http://www.whooo.net/ 發布人:昌盛機械
中空玻璃的第一道密封,靠的是丁基膠。這道膠打得好不好,直接決定中空玻璃的壽命——水汽一旦從密封層滲進去,玻璃內部起霧只是時間問題。而丁基膠涂布機的核心,說到底就一件事:把膠均勻、準確地打到鋁間隔條的兩側。
The first seal of insulated glass relies on butyl rubber. Whether this glue is applied well or not directly determines the lifespan of the insulated glass - once water vapor seeps into the sealing layer, it is only a matter of time before fog forms inside the glass. The core of the butyl rubber coating machine ultimately boils down to one thing: evenly and accurately apply the adhesive to both sides of the aluminum spacer strip.

膠嘴和鋁條的間隙,是有準確數值的。
The gap between the rubber nozzle and the aluminum strip has a precise value.
很多操作工憑手感調膠嘴位置,覺得“差不多就行”。但行業里的標準做法是:擠膠頭與鋁條的間隙調整為比鋁條寬度寬0.5mm。間隙過大,打出來的膠不粘、斷膠,吐出的膠呈圓形而非扁平狀;間隙過小,鋁條不容易通過,甚至卡住。這0.5mm的余量,是讓丁基膠既能均勻鋪展、又不至于擠到鋁框內側去的平衡點。
Many operators adjust the position of the glue nozzle based on their hand feel, thinking that 'almost enough' is enough. But the standard practice in the industry is to adjust the gap between the extrusion head and the aluminum strip to be 0.5mm wider than the width of the aluminum strip. If the gap is too large, the glue produced will not stick or break, and the glue ejected will be circular instead of flat; The gap is too small, making it difficult for the aluminum strip to pass through and even getting stuck. This 0.5mm margin is a balance point that allows the butyl rubber to spread evenly without squeezing into the inside of the aluminum frame.
打膠高度也有講究。成品中空玻璃的丁基膠內邊緣,應該與鋁框內邊緣相差0.5mm左右。距離太小,丁基膠會(huì )擠入中空玻璃內部,影響外觀;距離太大,密封層的有效寬度不夠,水汽阻隔能力下降。
There are also requirements for the height of the glue application. The inner edge of the butyl rubber of the finished insulated glass should be about 0.5mm away from the inner edge of the aluminum frame. If the distance is too small, butyl rubber will squeeze into the hollow glass, affecting its appearance; The distance is too large, the effective width of the sealing layer is not enough, and the water vapor barrier ability decreases.
溫度控制是另一個“看不見但明顯”的參數。
Temperature control is another 'invisible but deadly' parameter.
丁基膠是熱熔膠,工作溫度通常在120-140℃之間。溫度低了,膠的流動性不夠,出膠不連續、斷膠;溫度高了,膠料氧化變質,粘結力下降。有經驗的廠家會(huì )在膠箱里加氮氣保護,把氧含量控制在3%以下,減少熱熔膠氧化;同時設置定時攪拌,每隔15-20分鐘攪一次,避免局部過熱。溫控精度差的設備,膠條質量就不穩定,時好時壞。
Butyl adhesive is a hot melt adhesive with a working temperature typically between 120-140 ℃. The temperature is low, the fluidity of the glue is insufficient, and the glue is discontinuous and broken; The temperature is high, the rubber material oxidizes and deteriorates, and the bonding strength decreases. Experienced manufacturers will add nitrogen protection to the glue box to control the oxygen content below 3% and reduce the oxidation of hot melt adhesive; Simultaneously set up timed stirring, stirring every 15-20 minutes to avoid local overheating. Equipment with poor temperature control accuracy will result in unstable quality of the rubber strip, which may fluctuate between good and bad.
傳送帶速度和出膠量建議匹配。
The conveyor belt speed and adhesive output must match.
丁基膠涂布機的一個核心邏輯是:擠膠能力直接與傳動速度成比例。速度調快了,出膠量要跟著加大,否則膠條變細、覆蓋不夠;速度調慢了,出膠量要相應減小,否則膠堆積、溢出。好的設備通過PLC控制,設定好單位長度的擠出量(g/m)之后,速度改變時系統自動調整出膠量,保持恒定??咳斯な謩?dòng)跟著調,不僅累,而且跟不上。
A core logic of the butyl rubber coating machine is that the extrusion capacity is directly proportional to the transmission speed. The speed has been increased, and the amount of glue should be increased accordingly, otherwise the glue strip will become thinner and the coverage will not be enough; The speed has slowed down, and the amount of glue should be reduced accordingly, otherwise the glue will accumulate and overflow. A good device is controlled by PLC, and after setting the extrusion amount per unit length (g/m), the system automatically adjusts the glue output when the speed changes, keeping it constant. Relying on manual adjustment is not only tiring, but also unable to keep up.
膠嘴導向和壓輪,決定鋁條走不走直線。
The rubber nozzle guide and pressure wheel determine whether the aluminum strip can travel in a straight line or not.
鋁間隔條在傳送帶上是通過皮帶摩擦前進的。如果導向裝置不到位,鋁條會(huì )跑偏,打出來的膠一邊厚一邊薄?,F在的設備通常配膠嘴自動導向裝置,還有雙壓輪定位結構,讓鋁條在通過膠嘴區域時被夾持穩定,不左右晃動。壓輪壓下的速度也要調好——太快容易砸壞鋁條,太慢會(huì )阻擋鋁框前進,一般通過排氣節流閥來微調。
The aluminum spacer strip moves forward on the conveyor belt through belt friction. If the guiding device is not in place, the aluminum strip will deviate, and the glue produced will be thick on one side and thin on the other. The current equipment is usually equipped with an automatic guide device for the glue nozzle and a double pressure wheel positioning structure, which allows the aluminum strip to be clamped and stabilized when passing through the glue nozzle area, without shaking left and right. The speed of the pressing wheel should also be adjusted - too fast can easily damage the aluminum strip, and too slow can block the aluminum frame from moving forward. It is usually fine tuned through the exhaust throttle valve.
換膠效率是很多廠家忽略的生產瓶頸。
The efficiency of changing glue is a production bottleneck that many manufacturers overlook.
丁基膠用完要換膠缸,如果換一次要停機十幾分鐘,一天的產量就受影響了。有的設備設計了快速退缸功能,換膠只需十秒鐘左右。還有的膠缸可以自由回轉,放膠料更方便。這些細節在選型時不容易注意到,但用起來天天都在影響效率。
When the butyl rubber is used up, the rubber cylinder needs to be replaced. If it is replaced once, the machine will stop for more than ten minutes, which will affect the daily production. Some devices are designed with a quick release function, which only takes about ten seconds to change the glue. Some rubber cylinders can rotate freely, making it more convenient to put rubber materials. These details are not easy to notice when selecting, but they affect efficiency every day when used.
丁基膠涂布機不是復雜設備,但它的每一個參數都直接映射到中空玻璃的密封質量上。膠嘴間隙0.5mm、打膠高度0.5mm、溫度120-140℃、速度與出膠量同步——這幾個數字卡住了,膠條才能連續、均勻、粘得牢。
The butyl rubber coating machine is not a complex equipment, but every parameter of it is directly mapped to the sealing quality of the insulating glass. The gap between the glue nozzle is 0.5mm, the glue height is 0.5mm, the temperature is 120-140 ℃, and the speed is synchronized with the glue output - these numbers are stuck, so that the glue strip can be continuous, uniform, and firmly adhered.
本文由中空玻璃丁基膠涂布機友情奉獻。更多有關的知識請點擊:http://www.whooo.net 我們將會(huì )對您提出的疑問進行詳細的解答,歡迎您登錄網站留言。
This article is a friendly contribution from the hollow glass butyl rubber coating machine. For more information, please click: http://www.whooo.net We will provide detailed answers to your questions. You are welcome to log in to our website and leave a message.
- 膠嘴這個位置差0.5毫米,中空玻璃就等于白做 2026/10/09
- 雙組份打膠機:比例對了,膠才不白打 2026/10/05
- 全自動鋁條折彎機,中空玻璃鋁框加工核心利器 2026/09/29
- 全自動封膠線,中空玻璃廠升級繞不開的一道坎 2026/09/24
- 設備選型不對,密封失效是遲早的事 2026/09/23
- 中空玻璃生產線:別讓“手工中空”,吃掉你的利潤 2026/09/21
- 中空玻璃生產線:清洗出來不干凈,先查這五個地方 2026/09/18
- 中空玻璃生產線怎么確保玻璃的參數達標? 2026/09/16
- 中空玻璃生產線立著運行更具有效率 2026/09/14
- 全自動封膠線是中空玻璃密封的智能升級 2026/09/12
產品分類Product categories
聯系我們Contact us
- 咨詢熱線:0531-85717458 13705446998
- 公司地址: 山東省德州市齊河安頭鄉企巢工業園
- 掃碼聯系我們:

當前位置:



