中空玻璃生產線的使用壽命一般取決于中空玻璃生產線的清洗段和板壓段，那么，如何保養好中空玻璃生產線的清洗段和板壓段，就關系到整套中空玻璃設備的使用壽命，威力智能為您分享中空玻璃生產線的清洗段和板壓段如何保養：

The service life of a hollow glass production line generally depends on the cleaning section and plate pressing section of the hollow glass production line. Therefore, how to maintain the cleaning section and plate pressing section of the hollow glass production line is related to the service life of the entire set of hollow glass equipment. Power Intelligence will share with you how to maintain the cleaning section and plate pressing section of the hollow glass production line:

中空玻璃生產線清洗干燥段

Cleaning and drying section of insulated glass production line

中空玻璃生產線清洗機現在大多數廠家用的是不銹鋼，一般不會生銹,那重 點就是毛刷和電機的保養了，毛刷一般能用能長期使用，如果不脫 毛可以一直使用，只是他的下端軸承，因為濕度大容易生銹，造成毛刷銹住、抱死或阻力大等故障，還容易燒掉電機。威力智能提供的中空玻璃生產線的毛刷都是采用進口杜邦絲，清洗效果好， 不易脫 毛，可以長時間使用；而且去掉了海綿輥，既保證了玻璃不會二次污染，采用高壓風機循環熱風，保證吹干效果；再就是下端采用純鋼甚純銅軸承，大限度的隔絕生銹造成損失等情況的發生。

Most manufacturers now use stainless steel as the cleaning machine for insulated glass production lines, which generally does not rust. The key is to maintain the brush and motor. The brush can generally be used for a long time, and if it does not shed hair, it can be used for a long time. However, its lower bearing is prone to rust due to high humidity, causing problems such as the brush rusting, locking, or resistance, and easily burning the motor. The brushes on the insulated glass production line provided by Power Intelligence are all made of imported DuPont silk, which has a good cleaning effect and is not easy to remove hair, and can be used for a long time; Moreover, the sponge roller has been removed, ensuring that the glass will not be contaminated again. A high-pressure fan is used to circulate hot air, ensuring the drying effect; Another issue is the use of pure steel or even pure copper bearings at the lower end, which greatly isolates losses caused by rust.

中空玻璃生產線板壓段

Hollow glass production line board pressing section

再就是板壓機，特別是中空玻璃生產線內合片的板壓機有很多氣缸和電磁閥，如果不注意保養、加油、排水，很容易卡閥或燒線圈，特別是吸盤上的電磁閥不可以在油水分離器里加油潤滑，因為那樣會造成吸盤上也有油，污染玻璃。所以只能拔下電磁閥的進氣管用油壺加一點潤滑油。

Another issue is the plate press machine, especially the plate press machine for laminating in the hollow glass production line, which has many cylinders and solenoid valves. If maintenance, oiling, and drainage are not taken seriously, it is easy for the valve to get stuck or the coil to burn. Especially for the solenoid valve on the suction cup, it cannot be lubricated in the oil-water separator because it will also cause oil on the suction cup, polluting the glass. So you can only unplug the intake pipe of the solenoid valve and add some lubricating oil with an oil pot.

還有就是，丁基膠涂布機，也是需要注意保養的，在冷膠狀態不能退缸，因為冷膠狀態下膠和活塞是粘在一起的，如果強退，很容易把膠缸拔壞；再就是加膠時一定檢查好膠塊的外觀有沒有粘有鐵銷、小石塊和鐵釘等雜物，這些東西是很容易劃傷膠缸或堵住膠頭的。

Also, the butyl adhesive coating machine also needs to be maintained carefully. In the cold adhesive state, the cylinder cannot be removed because the adhesive and piston are stuck together in the cold adhesive state. If removed forcefully, it is easy to damage the adhesive cylinder; Furthermore, when adding glue, be sure to check the appearance of the glue block for any foreign objects such as iron pins, small stones, and nails, which can easily scratch the glue cylinder or block the glue head.